40 W (1/19 HP) AC Speed Control Motor and Controller (30:1 Gear Ratio) (Single-Phase 220/230 VAC) - DSCI540ECM-30V

Product specifications for DSCI540ECM-30V

The DSCI540ECM-30V specifies: This product has been discontinued, please contact your local sales office for more information.

Product Line	- Oriental Motor®
Motor Type	- AC Motor
Motor	- Induction
Frame Size	- 3.54 in, 90 mm
Output Power	- 40 W (1/19 HP)
Power Supply	- Single-Phase 220/230 VAC
Frequency (Hz)	- 60, 50
Current	- 0.55 A
Control Power Source	- 24 VDC ±10% 0.15 A or more
Shaft/Gear Type	- Parallel Shaft Gearhead
Gear Ratio (X:1)	- 30 :1
Output Shaft Diameter	- 18 mm
Electromagnetic Brake	- Equipped
Deceleration Control Function	- [Deceleration Control: ON (Factory Setting)] Variable Speed Range: 300 ~ 1400 r/min (50 Hz) 300 ~ 1600 r/min (60 Hz) Acceleration/Deceleration Time Range: 0.2 ~ 15.0 sec. [Deceleration Control: OFF] Variable Speed Range: 90 ~ 1400 r/min (50 Hz) 90 ~ 1600 r/min (60 Hz) Acceleration/Deceleration Time Range: 0.0 ~ 15.0 sec
Permissible Torque	- [Deceleration Control: ON, Vertical Operation] 31 lb-in [Deceleration Control: OFF, Horizontal Operation] 73 lb-in , [Deceleration Control: ON, Vertical Operation] 3.6 N·m [Deceleration Control: OFF, Horizontal Operation] 8.3 N·m
Variable Speed Range (r/min)	- [Deceleration Control: ON] 10 ~ 46 [50 Hz] 10 ~ 53 [60 Hz] [Deceleration Control: OFF] 3 ~ 46 [50 Hz] 3 ~ 53 [60 Hz]
Permissible Load Inertia	- 8800 oz-in², 1600 x 10-4 kg·m²
Permissible Overhung Load	- 0.39 in. from Shaft End = 112 lb, 0.79 in. from Shaft End = 157 lb, 10 mm from Shaft End = 500 N, 20 mm from Shaft End = 700 N
Permissible Thrust Load	- 33 lb, 150 N
Components	- 5IK40UECM-30 [Motor] DSC-MU [Speed Controller]
RoHS Compliant	- These products do not contain substances that exceed the regulation values in the RoHS Directive.
Safety Standards	- UL, CSA, CCC, CE
CE Marking	- Low Voltage Directives, EMC Directive
Insulation Resistance	- [Controller] 100 MΩ or more when measured by a 500 VDC between the main circuit terminal and the control circuit terminal, between the main circuit terminal and the case and between the main circuit terminal and FG after continuous operation under normal ambient temperature and humidity., [Motor] 100 MΩ or more when 500 VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity.
Dielectric Strength	- [Controller] Sufficient to withstand 1.9 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and the control circuit terminal, and between the main circuit terminal and the case, and 1.5 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and FG for 1 minute after continuous operation under normal ambient temperature and humidity., [Motor] Sufficient to withstand 1.5 kVAC at 50 Hz or 60 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity.
Temperature Rise	- A gearhead or equivalent heat sink is connected to the motor and the winding temperature rise is measured at 176ºF (80ºC) or less using the resistance change method after rated operation with no load under normal ambient temperature and humidity.
Overheat Protection Device	- Built-in Thermal Protector (automatic return type)
Ambient Temperature Range	- [Controller] 32ºF ~ 122ºF (0ºC ~ 50ºC), [Motor] 14ºF ~ 104ºF (-10ºC ~ 40ºC) (nonfreezing)
Ambient Humidity	- 85% max. (non-condensing)
Altitude	- Max. of 1000 m (3300 ft.) above sea level
Thermal Class	- 130 (B)
Degree of Protection	- IP20